Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Your Plumbing Crash Course: What You Must Have for Bathtub Installation
Blog Article
We've encountered this article pertaining to Tools You Need to Install a New Bathtub down the page on the net and reckoned it made good sense to relate it with you on this page.
Setting up a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily accessible, the task can relocate quickly; if you have to open up a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make sure you have certified yourself for the work and also are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly help you install a brand-new bathtub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't need to transform the arrangement of your previous water supply pipelines.
Your tools and also product checklist must make up the following:
Planning for the Setup
First of all, the supporting frame provided with the bath must be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. Once the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the required setting. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub till the level reads level.
To mount faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water as well as inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bathtub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bath tub should wait up until the bath tub has been used a minimum of when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer provided backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can break relatively early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about Installing A Bathtub, I thought sharing that segment was appropriate. Sharing is good. Who knows, you might be helping someone out. Thanks a lot for your time spent reading it.
The right fix? Ring! Report this page